Moisture, condensation, water in tumble dryer
If there is moisture, condensation, water in tumble dryer, refer to the suggestions below for step by step instructions.
Tumble Dryer:
Is there an error message on the display?
The error message can be a code on the display, a flashing LED or a sequence of beeps.
- If an error code is displayed, see the user manual for help troubleshooting the problem. (If you do not have your user manual, refer to Where can I find the user manual for my appliance?).
Is the ambient temperature between 5°C and 35°C?
If the ambient temperature is too low or too high, the tumble dryer may not operate correctly.
- Place the dryer in a room which has a suitable temperature.
- If the dryer is located in a room, make sure that the temperature of the room is between 5°C and 35°C.
- If the room temperature is not within this range, the tumble dryer may not operate correctly and will not heat up.
- Heat the room in which the tumble dryer is situated until it reaches a suitable temperature, or move the dryer to another room which is at a suitable temperature.
Did you select a steam cycle on your tumble dryer?
The steam cycle was selected.
- If you select a steam cycle on the tumble dryer, there will be a certain amount of steam inside the dryer’s drum.
- When the cycle is finished, there is condensation water inside the tumble dryer.
- This is perfectly normal when you use a steam cycle.
11.1 Cleaning the filter
At the end of the countdown, the filtering symbol will appear in the display. This means that the filter needs to be cleaned.
Note: The filter collects lint. Lint forms when the clothing in the tumble dryer dries.
![]() |
|
![]() |
|
![]() |
|
![]() |
|
![]() |
|
Tumble dryer with heat pump:
Is the load too much?
Overloading the product can reduce the heat circulation around the clothing.
- Redistribute the load and restart the drying cycle.
- If the load is too much, remove some of the clothing from the machine and restart the drying cycle.
Are the filters clean? Is the machine clean?
If the filters, condenser and/or heat exchanger are dirty, it may be the reason why the machine is not heating up.
- See the user manual for information on how to clean and maintain your appliance. (If you do not have your user manual, refer to Where can I find the user manual for my appliance?).
The filters may appear clean but still be blocked.
- You can check the filters by holding them up against the light or under a tap and seeing whether the water can flow through them.
- If no water passes through the filters, clean them and check them again.
- If water will still not pass through the filters, replace them.
- Filters and accessories are available via the Webshop. (You can visit our Webshop by clicking on the link below).
Examples of cleaning different types of tumble dryer:
11.3 Cleaning the heat exchanger:
If the symbol Heat exchanger is flashing on the display, inspect the heat exchanger and the space. Clean it if it is dirty.
How to perform the inspection:
![]() |
|
||
![]() |
|
||
![]() |
|
||
![]() |
|
||
![]() |
|
||
![]() |
|
Condenser tumble dryer:
Is the load too much?
Overloading the product can reduce the heat circulation around the clothing.
- Redistribute the load and restart the drying cycle.
- If the load is too much, remove some of the clothing from the machine and restart the drying cycle.
Are the filters clean? Is the machine clean?
If the filters, condenser and/or heat exchanger are dirty, it may be the reason why the machine is not heating up.
- See the user manual for information on how to clean and maintain your appliance. (If you do not have your user manual, refer to Where can I find the user manual for my appliance?).
The filters may appear clean but still be blocked.
- You can check the filters by holding them up against the light or under a tap and seeing whether the water can flow through them.
- If no water passes through the filters, clean them and check them again.
- If water will still not pass through the filters, replace them.
- Filters and accessories are available via the Webshop. (You can visit our Webshop by clicking on the link below).
Examples of cleaning different types of tumble dryer:
11.1 Cleaning the filter
At the end of the countdown, the filtering symbol will appear in the display. This means that the filter needs to be cleaned.
Note: The filter collects lint. Lint forms when the clothing in the tumble dryer dries.
![]() |
|
![]() |
|
![]() |
|
![]() |
|
![]() |
|
11.3 Cleaning the heat exchanger:
If the symbol Heat exchanger is flashing on the display, inspect the heat exchanger and the space. Clean it if it is dirty.
How to perform the inspection:
![]() |
|
||
![]() |
|
||
![]() |
|
||
![]() |
|
||
![]() |
|
||
![]() |
|
Tumble dryer with vent:
Is the load too much?
Overloading the product can reduce the heat circulation around the clothing.
- Redistribute the load and restart the drying cycle.
- If the load is too much, remove some of the clothing from the machine and restart the drying cycle.
Are the filters clean? Is the machine clean?
If the filters, condenser and/or heat exchanger are dirty, it may be the reason why the machine is not heating up.
- See the user manual for information on how to clean and maintain your appliance. (If you do not have your user manual, refer to Where can I find the user manual for my appliance?).
The filters may appear clean but still be blocked.
- You can check the filters by holding them up against the light or under a tap and seeing whether the water can flow through them.
- If no water passes through the filters, clean them and check them again.
- If water will still not pass through the filters, replace them.
- Filters and accessories are available via the Webshop. (You can visit our Webshop by clicking on the link below).
Cleaning the lint filter:
The filter traps all the lint that collects during the drying process.
- To ensure that the tumble dryer works properly, the filter must be cleaned after each drying cycle.
- The
FILTER warning light will remind you to do this.
Warning: Never start the tumble dryer if the lint filter is not fully inserted or if the filter is defective or clogged.
![]() |
|
||||
![]() |
|
Is the venting hose fitted correctly?
![]() |
When the hose is connected to the dryer, it should lead to the correct vent.
As regards the vent itself:
|
Is the vent open and clean?
On a vented tumble dryer, it is important that the vent, i.e. the hose/tube from the tumble dryer to the outside, and the air damper/non-return valve in the wall, are clean, so that the air from the tumble dryer can flow freely to the outside.
If the above does not resolve the problem, contact Authorized Service Center.
To help you determine the exact nature of the problem, we recommend a visit by one of our authorized engineers to check the appliance and fix the problem.
When contacting us, please have the following information to hand. You will find this information on the manufacturer’s data plate:
- Model number
- Product number (PNC)
- ELC number
- Serial number
Data plate with model number, product number/PNC, ELC and serial number:
![]() |
|
[3–9999] Where will I find the data plate on my product?
NOTE: Depending on the problem, you may be charged for a service visit by an engineer, even during the warranty period.
Make a note of the reported error code and quote it when you request an engineer. This will not solve your problem, but it will help our engineer identify the cause of the problem.
- Report error code: JD
Warning: We do not recommend using the product until the problem has been completely fixed. Unplug the product and do not plug it in again until you are certain that it is OK to do so.
You can request a visit by one of our engineers by clicking on the link below.